Dataman 48UXP Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Matériel Dataman 48UXP. Dataman 48UXP User Manual Manuel d'utilisatio

  • Télécharger
  • Ajouter à mon manuel
  • Imprimer

Résumé du contenu

Page 1 - Dataman-48UXP

Dataman-48UXP Intelligent Universal Pr

Page 2 - Acknowledgments

1 General Information CHAPTER

Page 3

Introduction The Dataman-48UXP is a high performance intelligent PC-based universal programmer that works through your

Page 4

Device-insertion and continuity checks – No mistakes! The Dataman-48UXP performs device-insertion and continuity checks before programming each devi

Page 5

Using the Dataman-48UXP Software Menus Accessing the menus can be done in two ways: 1. Use the mouse and click on the menu option displaye

Page 6

2 Installation CHAPTER

Page 7

Minimum PC System Requirements Win 95/98/ME, Win 2000, Windows XP, Win NT 4.0 or latest (NT OS system, need NT System ADM). CUP: PII 750 a

Page 8

installation program. 3. Following successful installation, run the software by executing Dataman-48UXP by double click the Dataman-48UXP ICON. The

Page 9

3 Command Hierarchy CHAPTER

Page 10 - CHAPTER

Dataman-48UXP Command Hierarchy System command Operation command Hot Key File (ALT-F) Save Buffer ALT-S Load File ALT-L Exi

Page 11 - Unbeatable speed

4 Operation CHAPTER

Page 12 - Device support summary

Copyright Notice This document is copyrighted, 2000, 2001, 2002 by DATAMAN PROGRAMMERS LTD. All rights are reserved. DATAMAN PROGRAMMERS LTD. reserv

Page 13 - Hot keys

LED Display The Dataman-48UXP has a three LED display to indicate the status of the socket. Read this section carefu

Page 15

File name Specify the destination and file name which you want to save to. File format Select the file format of your output file, click the right

Page 16

This writes the bytes 3,7,11,15, ... into the output file. 4th byte of 4 This writes the bytes 4,8,12,16, … into the output file. From Buffe

Page 19

File name This specifies the file name and its destination Auto Format Detected The software automatically detects the format of the file that

Page 20 - Save Buffer to File

To Buffer Address Starting address of the buffer to load the file into, if the data read is to be copy into a specific area of the buffer, fill in

Page 21

Exit Menu File / Exit Hot key Alt-X Quit the Dataman-48UXP program

Page 22

Project File Commands Save Project Menu Project / Save Project Hot key Alt-F1 This option saves the current setu

Page 23 - Load File to Buffer

How to use this manual Thank you for purchasing the Dataman-48UXP intelligent universal Programmer. We designed this manual

Page 24

This option is used to select a new device as the active device. It is important to select the correct device, as the algorithms used to program dev

Page 25

party adapter. Other useful example in device, package and adapter. 1) For example a 1M bit flash (29F010), this chip has three kind of packages, 32

Page 26 - From File to buffer

Keyboard Press TAB until the cursor is flashing in the “Type” box. Use the up and down arrows to go to the appropriate type. Press the space bar to

Page 27

such a function since the A9 location do not standardize for chip over 40 pin, using such a function may damage the chip since a 12V high voltage wi

Page 28 - Hot key Alt-X

menu and the contents is different from chip to chip), reference to device configuration section. The last set up menu is statistic configuration se

Page 29 - Change Device

Figure 4.2 mass production mode screen Editing the Buffer (memory device ) Menu Device / Edit Hot key Alt-E This function is used to e

Page 30

Radix This button controls the display of the memory address in Hex/Decimal format. If the address is currently displayed in decimal format, clicki

Page 31 - Mouse

Original file 01 23 45 67 89 AB CD EF after swap with word width 2. 23 01 67 45 AB 89 EF CD Original file 01 23 45 67 89 AB CD EF

Page 32

search string can be text code or hex code, it can search forward from cursor position or backward from cursor position. Next This commend is to fi

Page 33 - Mass-production Mode

In the mode, “X” refers to blown fuse, and “-“ refers to an intact fuse. The purpose of the buttons is as follows: Radix This button control the d

Page 34

Packing List Before you begin installing your Dataman-48UXP, please make sure that the following materials have been

Page 35

devices, the option is used to modify the vectors that will be used to test a device after the logical chip has been program, this test vector is us

Page 36

Insert You can insert a line of vectors by clicking this button. The position where the line will be inserted depends on the position of the cursor.

Page 37

N Power pin and the outputs not test X Output not tested, input default level Z Test input/output with high impedance

Page 38

Figure 4-4 Programming progress screen Verifying a Device Menu Device / Verify Hot key Alt- V This function compares the contents of the

Page 39

Figure 4-5 Device verification screen Memory Protect/program configuration Menu Device / Memory Protect Hot key ALT-U (PLD only) This

Page 40

will automatically program the main memory and program the configuration byte in a single command (program or mass production mode program). Special

Page 41 - Edit the test vector

Fourth Select the error display format. Important notice in function test To perform function test after program the PLD chip, the input file mu

Page 42 - Programming a Device

commend is to compare the buffer data with the device data, when the first data difference founded, the software will stop and report the buffer add

Page 43 - Verifying a Device

Options Modify Programming Parameters Menu Options / parameters modify Hot key F3 This function allo

Page 44

Figure 4-8 Example screen: Device-specific operation options The following options can be set: Start address, End address This is the start an

Page 45 - Special note for program

Contents Chapter 0 Quick Start ... 0-1 Quick Start...

Page 46 - Compare

buffer size is 80 (Hex), will therefore an end address of 3F. When selecting a start or an end-address, you should align the buffer on the right b

Page 47 - Device Configuration

ASCII Decimal Hex format example 0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17, … Modulo-26 format example A,B,C,D,E,F, … ,Z,AA,AB,AC, …. Insertion

Page 48 - Device Operation Options

(.) Twice Vcc ±5% When this option is selected, the Dataman-48UXP will do two verify passes on the device: one using Vcc+5%, the other Vcc-5%. Exam

Page 49

set up menu do not set the lock bit or protect bit enable. Auto-Erase/Overwrite Option This option only applies to chip, which is electronically e

Page 50

Statistic Menu Options / Statistics Hot key F6 Action Enable the counter or alarm when target count or maximum failure counter r

Page 51

Count how many verify operations into the display. Blank check enable: Count how many blank check activities into the statistic display Erase enabl

Page 52

Manufacture recommend the user can run self-test of Dataman-48UXP prior to each day’s operation. The self-test routine including testing the parall

Page 53 - Parallel Port Selection

Dataman-48UXP programmer need to return to your distributor for repair. The DAC (four DAC in Dataman-48UXP) test result and its meaning DAC0 25 34

Page 54 - Statistic

5 Using Adapters CHAPTER

Page 55 - Failure count

Adapter Requirements Dataman-48UXP supports universal 48-pin TSOP, 44-pin PLCC, 44 pin QFP, 44 pin TQFP, 44 pin SOP, 40-pin TS

Page 56

Programming a Device... 33 Verifying a Device... 34 M

Page 57

SDP-UNIV-16SO/170 16 pin SOIC (173 mil) universal adapter 1.27m pitch SDP-UNIV-20SO/200 20 pin SOIC (207mil) universal adapter for 8-20 pin SOIC

Page 58

SDP-UNIV-40TS/W 40 pin TSOP (10mm x 14mm) universal adapter for 40 pin TSOP Flash memory SDP-UNIV-40TSS 40 pin TSSOP universal adapter for 40 pin

Page 59

SDP-7096-100Q 100 pin QFP adapter for ALTERA 7096 SDP-7128-100Q 100 pin QFP adapter for ALTERA 7128/E SDP-7160-100Q 100 pin QFP adapter for ALTER

Page 60

SDP-C923-68 68 pin PLCC adapter for Microchip PIC 16C923/924 SDP-11K1-84 84 pin PLCC adapter for Motorola XC68HC11K1/K4 SDP-96MH-84 84 pin PLCC a

Page 61

LVT-640W18-56U uBGA adapter for Intel 28F320/640/128W18 (1.8Vcc, I/O) LVT-640W30-56U uBGA adapter for Intel 28F320/640

Page 62

SDP-A320-63F 63 pin uBGA adapter for AMD29DL32X (8x14mm size) SDP-41DL16-69F 69 ball FBGA adapter for AMD 41DL16xxMCP SDP-42DL32-73F 73 ball FBGA

Page 63

A Error Messages APPENDI

Page 64

Error Messages Cold not open file – nnnn! This file does not exist. You might have typed the wrong filename or you might

Page 65

Device inserted backwards or damaged already! The Dataman-48UXP detected that the device has been inserted the wrong way round, or that the device

Page 66

Dataman-48UXP not found! The Dataman-48UXP software does not detect the Dataman-48UXP on of the parallel ports, or the Dataman-48UXP may be failure

Page 67 - Device Code unmatched!

0 Quick Start This section is for experience user only, after install the Dataman-48UXP hardware and successfully install the system software in you

Page 68 - File write error!

have selected an incorrect device as active device, or the device is an older/newer version than the device supported by the Dataman-48UXP. Select

Page 69 - Dataman-48UXP not found!

Poor contact at pin %s! The Dataman-48UXP does an insertion test before programming/erasing etc. any device. This message indicates that the socket

Page 70 - Over current detected!

adapters. The system is in demo mode! The Dataman-48UXP was not found when the software was started up, and went into “Demo mode”. You can still ru

Page 71 - Poor contact at pin %s!

Quick Start After execution the Dataman-48UXP software, following Dataman-48UXP screen will display: It shows the fi

Page 72 - User break!

Read operation (Hot Key ALT-R), you can transfer the chip′s contents into the buffer. 4) Insert blank chip of the same type into the ZIF sock

Commentaires sur ces manuels

Pas de commentaire